Mar 11, 2017
Knowing if something is on or off can be extremely useful, but often you will want to know more. How bright is the light?
How fast is the satellite moving? These types of answers are often analog – they cover a large range of values, not just on or off.
The Arduino handles analog inputs with 6 dedicated pins, labeled A0 through A5. These pins have access to an analog-to-digital converter, which takes the range of input values and creates a digital version by cutting up the range into tiny pieces. All this is handled behind the scenes – all you have to do is use some very simple functions and you will get what you need.
You Will Need
Potentiometer (any resistance range will work)
Jumper Wires – at least 3
Bicycle tire
Step-by-Step Instructions
Place the potentiometer into your breadboard.
Run a jumper wire from the 5-Volt pin of the Arduino to either one
of the outside pins of your potentiometer.
Run another jumper wire from one of the ground pins on your Arduino
(labeled GND) to the other outside pin of the potentiometer.
Run the final jumper wire from pin A0 on your Arduino to the middle
pin of the potentiometer.
Plug the Arduino into your computer.
Open up the Arduino IDE.
Open the sketch for this section.
Click the Verify button on the top left side of the screen. It will
turn orange and then back to blue once it has finished.
Click the Upload button (next to the Verify button). It will turn
orange and then back to blue once it has finished.
On the menu bar, go to Tools > Serial Monitor – this will open
the Serial Monitor window – you should see numbers rolling down
this screen.
Now adjust the knob of the potentiometer and watch the serial
monitor window. The numbers should adjust between 0 and 1023.
Using the Arduino analogread and map function with a potentiometer
at pin A0
This image composed with Fritzing.
The Arduino Code
/*
AnalogReadSerial
Reads an analog input on pin 0, prints the result to the serial
monitor.
Graphical representation is available using serial plotter (Tools
> Serial Plotter menu)
Attach the center pin of a potentiometer to pin A0, and the outside
pins to +5V and ground.
This example code is in the public domain.
*/
// the setup routine runs once when you press reset:
void setup() {
// initialize serial communication at 9600 bits per second:
Serial.begin(9600);
}
// the loop routine runs over and over again forever:
void loop() {
// read the input on analog pin 0:
int sensorValue = analogRead(A0);
// print out the value you read:
Serial.println(sensorValue);
delay(1); // delay in between reads for stability
}
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
/*
AnalogReadSerial
Reads an analog input on pin 0, prints the result to the serial
monitor.
Graphical representation is available using serial plotter (Tools
> Serial Plotter menu)
Attach the center pin of a potentiometer to pin A0, and the outside
pins to +5V and ground.
This example code is in the public domain.
*/
// the setup routine runs once when you press reset:
void setup() {
// initialize serial communication at 9600 bits per second:
Serial.begin(9600);
}
// the loop routine runs over and over again forever:
void loop() {
// read the input on analog pin 0:
int sensorValue = analogRead(A0);
// print out the value you read:
Serial.println(sensorValue);
delay(1); // delay in between reads for stability
}
Discuss the Sketch
This sketch starts with a multi-line comment describing the sketch
and the circuit. You will probably notice that the first block of
code is the setup() function – we do not declare or initialize any
variables at the beginning of this sketch – instead we will do this
inside the loop() function, as in the last example. Inside the
curly braces of setup() we revisit the Serial library and use the
function Serial.begin().
void setup() {
// initialize serial communication at 9600 bits per second:
Serial.begin(9600);
}
1
2
3
4
5
6
7
void setup() {
// initialize serial communication at 9600 bits per second:
Serial.begin(9600);
}
If you recall from the last lesson, Serial.begin() takes the baud
rate as an argument (this will almost always be 9600). This
function allows you to setup a communication channel between the
computer and the Arduino. As you may know by now, setup() only runs
once, and then we move on to the next block of code.
But wait! Don’t we have to set the mode of the pin we will be using? Great point!
What the Arduino does, by default, is set all the pins on the board as INPUTs unless you tell it otherwise. So in many cases, you do not have to explicitly set a pin as an input using the pinMode() function. That being said – I make it a habit to do this anyway – because it makes things clear to me – and that is worth it in space and effort.
So I dare you, set the mode of the pin using the pinMode(A0, INPUT) function inside the curly braces of setup()– you won’t regret it.
Moving on to the loop() function, we start with a variable declaration and initialization.
int sensorValue = analogRead(A0);
1
int sensorValue = analogRead(A0);
We declare a variable called sensorValue and we initialize it to
the output of a new function. This new function is the glamorous
analogRead(). So take a wild guess what this new function
analogRead() does. It reads the value at the analog pin that you
have chosen – in this case, it is the analog pin A0, where we have
the center pin of the potentiometer connected. The voltage at pin
A0 will be mapped to a number between 0 and 1023, and this value
will be assigned to the variable sensorValue.
If you recall from above, the actual voltage at pin A0 will be between 0 and 5 volts, depending on where your potentiometer is adjusted – this value gets mapped to the range 0 – 1023 with the help of the analog-to-digital converter. So we have a variable that has recorded the value at our potentiometer – what next? Well, let’s look at the value. To do that, we need to print it from the Arduino to our computer – and you guessed it, we will use the Serial library function println() to do just that…
Serial.println(sensorValue);
1
Serial.println(sensorValue);
No big surprises here – we send as an argument the sensorValue
variable to the function Serial.println() and our serial monitor
window will display the resulting values.
To finish the sketch, we invoke the delay() function for one millisecond to make sure our next reading is a stable one and we start at the top of the loop() again. We record a new value using analogRead(), save it to the variable sensorValue and then print it to the computer.
All this is good and well, you might be thinking, but what does a potentiometer have to do with sensors? A potentiometer doesn’t sense anything! You are right – but interestingly, many sensors work by applying the same principle that a potentiometer does – adjusting resistance. Take a photo-resister for example – it can be used to sense light – because the resistance changes based on the brightness of light that it is exposed to – this change in resistance will adjust the amount of voltage that a pin on the receiving end will receive. So now the ball is in your court – what can you use analogRead() for?
Try On Your Own
Change the analog pin to A2. Make adjustments in the code and the
circuit.
Try a different potentiometer in the circuit, does it affect the
range of values displayed?
Further Reading
analogRead()
Analog Input Pins
potentiometer tutorial – this is good